Save $10 off $199 | $25 off $499 | $50 off $999 using the code SUMMERSAVE at checkout. Excludes orders containing MAP items.
FCP Euro Save On Accessories and Detailing Products

If your engine is having problems running, and your diagnosis includes low fuel pressure and/or abnormally loud engine bay noises, it may be time for a new fuel pump.

Most 911s have an external, electric fuel pump located right beneath and behind the fuel tank at the front of the car. It is very easy to access and service should it ever require replacement. Some early 911s have a mechanical or electric fuel pump located in the engine compartment. There are so few of those, however, that we'll only cover the front pump replacement procedure for demonstration purposes. 

Model Years Applicable:

All Porsche 911 models up to 1989.

Tools Needed To Complete This Repair:

  • Floor jack
  • Jack stands
  • Flat and Phillips screwdrivers
  • Metric socket set
  • Channel lock pliers
  • Fuel line clamp or very small C-clamp
  • Rags for fuel spill cleanup
  • Rubber gloves
  • Safety glasses
  • Fire extinguisher

Parts Needed:

  • 1 Fuel pump
  • 1 Fuel pump check valve (and three replacement crush washers; usually included)
  • Electric connection rubber boots (if any are damaged/missing)

Fuel Pump Replacement Procedure

Caution: When working with the fuel system, always take fire safety precautions.

  • Disconnect negative battery terminal.
  • Keep a fire extinguisher nearby.
  • Work in a well-ventilated area with no sources of heat, spark, or open flame.
  • Make sure the fuel tank has as little fuel as possible to reduce the chance of gasoline spillage.
  • Work with as much ambient and overhead lighting as possible to keep electric work lamps away from the fuel pump area.
  • Gasoline is carcinogenic so wear rubber gloves, long sleeves, and safety glasses to protect your skin.

Step 1: Raise Car And Support With Jack Stands

Raise your car on jack stands using this procedure. We will be working in the space between the front wheels, which is quite cramped. In order to give you the most room to move around, it's recommended that the entire car be raised on stands for easy access.

Step 2: Locate & Remove Belly Pan

Locate the rectangular belly pan between the front wheels. Remove the four fasteners holding it in place. On this particular car there are two bolts and two nuts holding it in place. Be careful as it is a fairly heavy piece of sheet metal and you don’t want it falling on you. On some cars, two of the belly pan mounting points are shared with the front sway bar mounts so you may see the sway bar rotate slightly as you remove the bolts or nuts.


Once the belly pan is removed, you should see the fuel pump which is shaped like an energy drink can with hoses connected on both ends.

Step 3: Clamp Fuel Line

Gently clamp the short fuel line between the tank and the fuel pump inlet to pinch off fuel flow and prevent fuel spillage. You can use a very small C-clamp with no sharp edges on the two clamping surfaces. Clamp just hard enough to pinch the line shut and not hard enough to sever the line.


 Step 4: Disconnect Fuel Pump

The fuel pump will have two electrical terminals labeled “+” and “-“. Write down which color wire goes with which polarity terminal for easier reference later on. If any of the rubber boots covering the pump terminals are damaged, plan on replacing them along with the pump. Disconnect the wires and tuck them out of the way for now.

Loosen the small hose clamp on the pump side of the short fuel line between the tank and the pump. Pull the hose off and verify the clamp has stopped fuel from flowing. A small amount of fuel may spill from inside the pump so have a rag ready for cleanup.

On the outlet side of the pump, there will be a banjo fitting for the pressurized fuel line going to the engine. Loosen the hex cap at the end of the banjo fitting. This may be tricky because the pump may want to turn as you apply torque to the hex cap. Some penetrating oil on the hex cap may help. You may be able to get a pair of channel lock pliers or an open-ended wrench on the flat faces of the hex feature on the outlet side of the pump to hold the pump fixed while you turn the hex cap. Once the hex cap is loose, spin it off and remove the banjo fitting along with the two crush washers. More fuel may spill from inside the pump body and/or the banjo fitting so have a rag ready.

Loosen the large hose clamp holding the pump body in place. The pump body is now free to be removed from the car. If there is a rubber cushion between the hose clamp and pump body, save it for re-installation later.

 Step 4: Replace The Check Valve On New Pump

Many 911 fuel pumps will have a check valve screwed into the outlet of the pump body. If yours has one, it's a good time to replace this inexpensive part. Unscrew it from the body of the old pump to verify it's actually a check valve and its orientation. Then install a new check valve onto the outlet of the new pump with a new crush washer and tighten by hand. Some 74-79 911s came with an OE pump with an internal check valve. If this is the case in your car, it's OK to replace it with the same kind of internal check valve pump or a regular pump with an external check valve.

 Step 5: Install New Pump In Car

 Now re-install the pump in the reverse order as the removal.

  • Reinstall the pump and the rubber cushion on the large hose clamp in the same orientation as before.
  • Reconnect the banjo fitting for the pressurized line going to the engine to the pump outlet with two new crush washers and tighten the hex cap by hand. Be gentle when holding the pump body steady during tightening so you do not damage your new pump.
  • Reconnect the short fuel line from the fuel tank to the pump inlet and tighten the small hose clamp. Release the C-clamp cutting off fuel flow from the tank.
  • Reconnect the electrical terminals with the same polarity as before.

 Step 6: Test And Check For Leaks

If the tank is currently empty, pour in some gas. Turn the engine on for a few minutes and check for fuel leaks. The car may take a few extra cranks firing up for the first time with the new pump as air is purged out of the fuel lines. If there are no leaks, it’s time to re-install the belly pan.

 Step 7: Re-Install Belly Pan

 If your front sway bar moved as you first removed the belly pan, you will have a difficult time pushing it back into place to allow the belly pan to bolt back in. If this is you, you will have to take your floor jack or a bottle jack to gently push on the sway bar arm, just outside of the belly pan area (slightly outboard of the front torsion bars). Do not keep cranking on the jack and lift the car by the sway bar! The idea is to put a slight force on the bar itself to get it to rotate back into its normal bolted-down position. You should now be able to place the belly pan into position and hand-tighten the bolts and nuts snug. At this point release the jack from the sway bar and finish tightening all the belly pan fasteners.


 Your fuel pump is now ready to give you years of reliable service. As always, if you have any questions, don't hesitate to leave them in the comments below or email

author image
Written by :
Jose Martinez

Having explored the fields of aerospace, power generation, automotive aftermarket, and concept car engineering, I'm now a development engineer for Mazda North America. In my spare time, you can find me wrenching on anything, but mainly cars of the air-cooled variety. @joe_engineer

More Related Articles

How To Code BMW N54 Injectors With An Autel MX808
FCP Euro Save On Accessories and Detailing Products
5 Tips To Maintain Your Car During Long-Term Storage
How To Read Your BMW N55 Crankshaft For Bearing Codes
How To Pick The Right Coolant For Your Car 
© FCP Euro 2024. All rights reserved.  
Version: 8881f0604