Save $20 off $199 | $50 off $499 | $100 off $999 using the code SUMMERFIX at checkout. Excludes orders containing MAP items.
FCP Euro Brake Kit Sale


Chances are that many of you have received the common "Anti-Skid Service Required" message from your P2 Volvo. If you haven't, there's a good chance that you may come across it during the span of owning your vehicle. This common error message tends to be found the most on the P2 platform vehicles ranging from model years 2005-2010.

The most common cause for this message is due to a faulty steering angle sensor. The steering angle sensor is incorporated into the Supplementary Restraint System (SRS) contact reel which is actually part of your steering wheel module. Inside of the steering wheel sensor is a code wheel which follows the movement of the steering wheel and calculates the steering wheel angle, turning speed, and number of turns.

The first step to remedy this issue would be to upgrade the steering angle sensor software. If the software has been installed and the sensor re-calibrated but the error message still remains then a new steering angle sensor must be installed.


Step 1: Disconnect the battery and wait about 5 minutes before performing any work - Safety first.

Step 2: Remove the 3 T-25 torx screws from the steering column covers - Remove the covers

Step 3: Insert the key into the ignition to free the steering lock. Turn the wheel a quarter turn on each side to expose the two holes on the rear of the wheel. Insert a flat head screwdriver into the hole and pry up so that the screwdriver presses down on the catch release. Do this in both holes. This will release the air bag from the steering wheel.

Step 4: Take note of the wiring and the colors of the connectors. The connector housing on the airbag with either be pink or green to match the pink or green connector housings on the wiring harness. Remove the two connectors. Remove the green connector for the Steering Wheel Module.  Place the air bag off to the side with the airbag portion facing up. Caution: Do not place the airbag surface on the ground or rest area, the connector side should always be placed on the ground or rest area.

Step 5: Remove the key and lock the steering wheel by turning it. Once the column is locked you can then remove the 18 mm bolt securing the steering wheel to the steering shaft.

Step 6: Once the bolt is removed, this will expose the steering shaft spline area. With a Sharpie marker, make a mark on the steering wheel splines so that they transfer onto the steering shaft splines. This will be used later so you know exactly where to re-position your steering wheel.

Step 7: Remove the steering wheel.

Step 8 : Now that you have the Clockspring / SAS unit completely exposed you'll notice the 3 Phillips head screws - Remove them.

Step 9: Remove the connector on the left side of the SAS.

Step 10: Replace the unit. When removing and installing be sure to remove and install it perfectly straight to avoid bending the terminal pins.

Step 11: Reinstall using the previous steps in reverse.

NOTE!: The new unit will come with a small torx screw inserted into a window at the top of the unit. This screw is used to lock the unit into place to prevent failure or damage to the unit and to prevent it from moving while in transit or during installation. IT IS IMPERATIVE THAT YOU REMOVE THIS TORX SCREW ONCE THE UNIT HAS BEEN INSTALLED. Leaving this screw installed will cause failure!

Once the new unit has been installed there is a good chance that if you have the latest software already installed into the vehicle, that the unit will not need to be reprogrammed. It's also recommended to have an authorized repair facility perform a calibration of the unit (DSTC ONLY). This should not take more than 5 minutes of the repair facility's time. At this time it's also a good opportunity to have them clear any DTCs that are still left in the system.

Check out our DIY Repair Video HERE:




author image
Written by :
Jay VanGorden

Jay has been with the company since 2011. He's been in the automotive industry for over 25 years and brings a great amount of automotive experience to FCP Euro. He graduated from Universal Technical Institute of Exton PA. in 2005 and then went on to graduate from the Volvo S.A.F.E program in 2006. From there he worked at a Volvo dealership for 7 years before joining the FCP Euro team achieving his ranking as a Certified Volvo Technician in 2 years, and a Master Volvo Technician in 4 years. During his tenure, Jay VanGorden has worked in multiple areas and roles within FCP Euro and is currently the VW Catalog Manager.

More Related Articles

The 5 Least Expensive New European Cars In 2024
Five Modern European Minivan Alternatives
FCP Euro Brake Kit Sale
How To Pick The Right Coolant For Your Car 
Volvo AWD Systems Explained
Volvo S60 & V60 Buyer's Guide (P3 Chassis)
© FCP Euro 2024. All rights reserved.  
Version: cd8b70308