Question Posted by a customer
Returning customer here. I have the error codes: 131501 VANOS. Inlet, Cold Start: Not Controllable, 0 120408 Boost Pressure Control, Cut-Off: Pressure Rise Blocked P052B Cold Start “A” Camshaft Position Timing Over-Retarded Bank 1 Engine would turnover, but it will start to shake very bad and cause a weird noise. Prior to this I replaced the oil filter housing gasket and did an oil drain. Would this sensor resolve this issue?
Answer (Posted by FCP Euro Products Team)
This sounds like a comprehensive issue that will most likely take an in-person diagnosis. The only thing we can think of is a blockage was loosened and made its way into a solenoid valve or VANOS actuator, but with the information provided we are unable to provide any specific diagnosis
Question Posted by Darren
Where is the location of the camshaft sensors on a 2014 550i.
Answer (Posted by FCP Euro Products Team)
On the valve covers towards the front of the engine.
Question Posted by Christopher
Code 2a7c, could this sensor be the culprit??
Answer (Posted by FCP Euro Products Team)
No. The code in question is related to VANOS control which has nothing to do with the cam position sensor. In fact, this code indicates that the cam sensor is working correctly since there is a correlation fault between desired cam position and the actual cam position. This fault is likely related to a VANOS solenoid that is dirty not allowing for proper oil flow to the cam adjuster or another mechanical issue related to the VANOS adjuster itself.
Question Posted by Russell
We have a 2007 BMW X3 3.0si, this BMW X3 needs 2 camshaft sensors? Just to make sure, are the intake and exhaust camshaft sensors the same sensor?
Answer (Posted by FCP Euro Products Team)
Yes, they are the same sensor.
Question Posted by Ronald
Will This Cause a Transmission Gear ratio monitoring code?
Answer (Posted by FCP Euro Products Team)
No. Typically this code is presented when your vehicle's transmission is having trouble going into gear due to the mechatronic adapter failing. While we cannot confirm this is the issue you are having without being at the vehicle, please refer to p/n: 24347588724 for the mechatronic adapter accordingly.
Question Posted by a customer
I have a 2013 X5 50i M package and I have codes P052D, P05CD, and P0022. Oil change was done a month ago but I now see the computer saying its overfilled. Car drove completely fine today and randomly went into limp mode and now after start up and roughly 5-10 sec it goes right back into it. I had P0022 with limp mode before the oil change too, and then the oil change fixed it. What should I do? I am thinking about ordering this and the vanos sensor just in case with first doing an oil change with the correct amount.
Answer (Posted by FCP Euro Products Team)
Replacing a camshaft position sensor will not fix a camshaft correlation fault code. It is also highly unlikely that a VANOS solenoid (that's what we're assuming you mean by VANOS sensor) will resolve the issue either. The VANOS system is controlled by oil flow to the cam adjusting unit. Oil flow is controlled by the solenoid based on what is required by the DME. Our recommendation is to start by making sure the oil level is correct.
Question Posted by a customer
For a 08 BMW X5 4.8i are all 4 sensors the same? Thanks
Answer (Posted by FCP Euro Products Team)
There are two (2) camshaft position sensors on the E70 X5 4.8. The other two sensors are the intake and exhaust cam VANOS solenoids.
Question Posted by a customer
I’m get this code p0393 on my 2010 bmw x5 4.8i will this solve the problem? where is it located on my suv ?
Answer (Posted by FCP Euro Products Team)
It is impossible to say this p/n will fix the code without being present at the vehicle. The camshaft position sensor measures the position of the camshaft; So while you are getting a code, the sensor may also be doing its job in determining any faults within the system. It is recommended to start by inspecting the sensor itself to determine its condition as it is common to have the sensor short out on itself on higher mileage vehicles.
Question Posted by a customer
06 325i- I am getting P0015 and P0012 timing retarded. I have replaced Variable Timing Solenoid both on front of motor and I have replaced the big VVT solenoid on top of motor completed oil change and replaced plugs. Next option?
Answer (Posted by FCP Euro Products Team)
We have touched base on this problem in other Q&A's. Our recommendation is to 100% diagnose the system. We cannot recommend parts based on the fault codes alone as the fault codes describe a running condition, a running condition that could be the result of one or several problems in the entire VANOS system: P0012 and P0015 fault codes themselves help identify an irregularity in a systems functions but is not a prompt to replace parts until said parts are deemed to be the issue. P0012 and P0015 are not faults associated with bad cam sensors usually. In fact, the codes suggest that the cam sensors are working just fine. Generally speaking the most common sources of issues for the faults in question are due to: - The variable camshaft timing (VCT) oil control valve (OCV) is stuck in the open position. - The camshaft phaser is stuck in the retarded position due to damage or clogged oil passages. - Oil flow problems to the VCT piston and phaser from incorrect oil viscosity. - The OCV has an open circuit or the ECM has an open circuit. There are a few potential trouble areas that can cause the above codes including clogged/dirty solenoids (which can be cleaned), camshaft rectaring failure (loss of oil pressure to cam phasers), or issues with the non return valves in the cylinder head (lack of oil for VANOS system).
Question Posted by Eric
Hello, i have a 08’ 335i N54 & am getting codes 2FDA/2FDB (crankshaft missing & not plausible) but already changed the “crankshaft” sensor…along with these codes the car is shaking when coming to a stop and was wondering if these “camshaft” sensors could be the issue & reason why i’m still getting these codes even after replacing crankshaft sensor?
Answer (Posted by FCP Euro Products Team)
Most likely not. Cam/crank correlation fault codes are rarely ever fixed by replacing cam position sensors. One thing to look into would be your HPFP (High Pressure Fuel Pump) as error code 2FDA/2FDB correlate to "fuel high pressure." This is a common fault item on N54 335i vehicles, especially if your vehicle is tuned by an aftermarket software. I would start with verifying the HPFP is functioning properly before anything by testing fuel pressure. If you have adequate fuel pressure, we recommend bringing your vehicle to a local BMW Dealership/Authorized BMW Repair facility to have it properly diagnosed.
Show more questions (15 more)