Question Posted by Selvin
Hi I'm having an intermittent error code 130104 (2013 f30 335I) I have replaced the intake vanos solenoid and and have done an oil change but the error still comes up, one of the suggestions is to replace the camshaft sensor. My question is do you think that changing the camshaft sensor would fix the issue?
Answer (Posted by FCP Euro Products Team)
Most likely not. Cam/crank correlation fault codes are rarely ever fixed by replacing cam position sensors. Since the system is hydraulic in function two things need to be determined: 1) Are the cams and crank mechanically out of time> 2) Is oil pressure to the camshaft actuators adequate for actuation?
Question Posted by Richard
I have a P052 code could this be associated with Cam Sensors or Vanos Solenoids ?
Answer (Posted by FCP Euro Products Team)
P052 appears to be an incomplete fault code. P052B seems to be what you most likely would have (A Camshaft Position Timing Over-Retarded Bank 1) which is the intake cam position location being in a retarded timing position. The reason for this fault code is several possibilities and is less likely to be a cam sensor-related issue. Since the VANOS system works using hydraulic pressure (uses engine oil) oil flow to the cam could be a problem, the camshaft bearing ledges have worn allowing oil to pass by the sealing rings on the cam, carbon/obstruction in the oil passages, oil non return valves not working properly to maintain oil volume in the cylinder head, the cam reluctor ring has slipped out of position (usually due to the cam bolt starting to break), engine has skipped timing, VANOS hub is faulty, ad other associated reasons. Bottom line, it's not highly likely the problem is related to the cam sensor. This is generally a mechanical related fault code. A complete system diagnostic needs to be performed to determine the reason for the code,
Question Posted by a customer
Hello, I have a 328xi 2008, and I have the code 2A82 and POO12 that appears, I have replaced my vanos and the codes come back... Is that what it could be for sensors?
Answer (Posted by FCP Euro Products Team)
No. Your issue is not a cam sensor problem. In fact, the code suggests your cam sensor is working perfectly fine. Not sure what you mean when you say you replaced your VANOS (solenoids or cam gears for example) but the VANOS system requires oil pressure to work. Are the check valves in the cylinder head working correctly? Are the camshaft recatring seals in poor condition allowing for oil to leak past? There are several other mechanical issues that can cause the problem you are having.
Question Posted by Stan
I have a 2011 bmw x5 with a p0341 code would this be the right thing to replace and would I need one or two?
Answer (Posted by FCP Euro Products Team)
Most likely pending there are no wiring issues.
Question Posted by a customer
I have a bmw 328i! So I have bought two of this exact ones now I was researching and I found out they were different. One is for the exhausts. Can I put the same two camshaft sensors on both of them or I need a different camshaft sensor part?
Answer (Posted by FCP Euro Products Team)
The same cam sensor is used for the exhaust and intake cam for 328i models from 2007-2016.
Question Posted by a customer
I have a 2A9A - “ crankshaft - inlet camshaft, synchronization” code in my 07 335 e92 N54... the car cranks but will not start up...could this part fix my issue....
Answer (Posted by FCP Euro Products Team)
No, replacing a cam sensor will not fix your issue. The code in question actually suggests the intake cam sensor is working perfectly fine and is measuring the position of the intake relative to the crank as being way off. This could be due to several reasons include a timing problem, an issue with the intake cam VANOS hub, etc. Since the engine won't start on this one code we advise looking to make sure the VANOS hub bolt which secures the VANOS gear to the cam has not sheared.
Question Posted by a customer
I have a 2009 BMW 550i N62 I have P0012 and P0018 I swapped cam sensors on bank 1 and code changed from P0012 to P0016 could this indicate that one cam sensor is bad? And if I get the same result on bank 2 where the code changes could it mean I have 2 bad sensors?
Answer (Posted by FCP Euro Products Team)
P0016, P0018, P0012, and P0016 are camshaft to crankshaft correlation codes which could be the result of the camshaft timing is out of position due to the timing chain jumped teeth, the camshaft phaser is out of position due to problems with the phaser, the oil has flowed to the phaser is impeded from having an incorrect oil viscosity or partly clogged passages, or the Oil Control Valve (OCV) has a restriction in the OCV filter. The only time cam sensors are generally a probblem is when fault codes suggest a short circuit or open in the circuit. The codes you have suggest the cam sensors are working perfectly fine and the issue is actually a variable cam timing problem.
Question Posted by Marcus
I have an intermittent 2A98 DME: Crankshaft-inlet camshaft reference code, along with 3100 DME: Boost-pressure control Deactivation. The car runs fine and after car has warmed up the code doesn't come back once cleared. This doesn't happen in summer months though, only in the winter and autumn when outside temps get below about 50 degrees. Its been a pain for a while having to warm up the car then restart it to get it to run properly. could this sensor possibly be the culprit? Thanks in advance for any help you can provide.
Answer (Posted by FCP Euro Products Team)
No, this cam position sensor is not going to be the source of your problems. Here is a really good article from Autologic that explains this fault code and possible sources of the problem: https://us.autologic.com/news/bmw-vanos-system-fault-testing-and-diagnosing
Question Posted by a customer
I have a 2009 328i with a service engine soon light on. I got code p05CE. Looking it up online says Cold Start 'B' Camshaft Position Timing Performance (Bank 1) Is this the correct part for that? I am trying to help my husband by ordering these.
Answer (Posted by FCP Euro Products Team)
The fault code is not suggestive that a camshaft position sensor is faulty, rather it suggests there could be an issue with the variable cam timing (VANOS) system which is common for your year/model. The issue could be something as simple as a bad oil check valve in the cylinder head or an issue with the VANOS solenoid. We recommend having the vehicle diagnosed before ordering parts.
Question Posted by a customer
I have a 07 BMW X3 and 2 codes popped up P0012 and P0015 (A&B camshaft position timing, over retard bank) will replacing the camshaft position sensor and both VVT solenoids help with those codes? Thanks I’m advanced.
Answer (Posted by FCP Euro Products Team)
We recommend a complete diagnosis on the vehicle first before ordering parts. Faults codes themselves help identify an irregularity in a systems functions but is not a prompt to replace parts until said parts are deemed to be the issue. P0012 and P0015 are not faults associated with bad cam sensors usually. In fact, the codes suggest that the cam sensors are working just fine. Generally speaking the most common sources of issues for the faults in question are due to: - The variable camshaft timing (VCT) oil control valve (OCV) is stuck in the open position. - The camshaft phaser is stuck in the retarded position due to damage or clogged oil passages. - Oil flow problems to the VCT piston and phaser from incorrect oil viscosity. - The OCV has an open circuit or the ECM has an open circuit. There are a few potential trouble areas that can cause the above codes including clogged/dirty solenoids (which can be cleaned), camshaft rectaring failure (loss of oil pressure to cam phasers), or issues with the non return valves in the cylinder head (lack of oil for VANOS system).
Show more questions (5 more)